Cirrus-logic CS8130 Manuel d'utilisateur télécharger pdf



Cirrus Logic, Inc. 1997

Cirrus Logic, Inc.

P.O. Box 17847, Austin, Texas 78760

(512) 445 7222 FAX: (512) 445 7581

http://www.cirrus.com

11/6/97

CS8130 Revision G Addendum

Multi-Standard Infrared Transceiver (DS134F1, SEP ‘05)

The following items represent permanent changes to the specification of the CS8130 IR transceiver.

1) The Silicon Revision Register (Register 28) reads 0010, indicating rev G silicon.

2) The default receive sensitivity setting is changed to 00011 (Register 6 resets to 0011).

3) Oscillator low power mode is now the default condition after reset (Register 21 resets to 0100).

4) The BLKR bit (Register 4, bit D2) blocks the RXD output data during those periods when the transmit

LEDs are on. This prevents the UART/system reading the transmitted data. The re-enable signal for

the receiver is delayed by 8 µs from when the LEDs are turned off. Set to 1 to block RXD data, set to

0 to allow RXD data through during transmission. This bit goes to 0 upon RESET.

5) An additional control bit was added which causes the CS8130 receiver to ignore the falling edge of the

IR pulse. This bit is called ENPOS, and it is bit D2 of Register #7. ENPOS is normally 1, which causes

the falling edge to be ignored. This results in greater range in IrDA and high-frequency ASK (Sharp

500 kHz) modes. ENPOS should be set to 0 for low-frequency amplitude modulated modes.

6) For IrDA/HP-SIR pulse width modes, two additional control bits have been added:

a. The THIN bit (Register 7, bit D1) allows the minimum acceptable pulse width to be reduced from

1 µs to 0.5 µs when set to 1. This bit has effect only when the receiver is programmed to mode 1a

(fixed 1.6 µs pulses only) or 1c (receive 1.6 µs to 3/16 of a bit cell pulses). This bit resets to 0.

b. The WIDE bit (Register 1, Bit D2) expands the maximum allowable pulse width to 9/16 of a bit

cell when set to 1. This bit has effect only when the receiver is set to mode 1a (fixed 1.6 µs pulses

only).

For normal IrDA operation, it is recommended that THIN be set to 0 and WIDE be set to 1. Under these

conditions, the qualification boundaries for receiver mode 1c (receive 1.6 µs to 3/16 of a bit cell pulses)

are identical to the qualification boundaries for receiver mode 1a (fixed 1.6 µs pulses only). This bit

resets to 1.

7) A TV remote receive mode hesitate bit has been added (Register 1, Bit D3). When this bit is set to 0,

the RXD pin will remain high until the first valid IR signal is detected. At that time, the RXD pin will

output serial data at the specified baud rate until the receiver is disabled (Register 0, bit D1). If this bit

is set to 1, the RXD pin will immediately and continuously output data. This bit resets to 0.

8) The ASK transmit carrier frequency formula has changed:

MD=(3.6864E6/FR)-2 , where MD is the Modulator Divider Value and FR is the desired modulation

frequency (Registers 10 & 11). The RESET default value for MD is now 5, yielding a default carrier

DS134PP2-B

NOV ‘97

http://www.cirrus.com

CS8130

SEP ‘05

DS134F1-B

http://www.cirrus.com

MAR ‘06

DS134F1-B1

http://www.cirrus.com

MAR ‘06

DS134F1-B1

http://www.cirrus.com

MAR ‘06

DS134F1-B1

1 2 3 4

Résumé du contenu

Page 1 - CS8130 Revision G Addendum

Page 2 - 2 DS134F1-B1

2 DS134PP2-Bfrequency of 527 kHz.9) ASK Receive Choices - valid incoming frequency range (with RATS = 0 and MD = 5) is 431 kHz to609 kHz.10) RATS regi

Page 3 - RECEIVER CHARACTERISTICS (T

DS134PP2-B 3RECEIVER CHARACTERISTICS (TA = 25 °C; V+ = 3.0 V, Digital Input Levels: Logic 0 = 0 V,Logic 1 = V+; unless otherwise specified)Notes: 5. T

Page 4 - REVISION HISTORY

4 DS134PP2-BDIGITAL PIN CHARACTERISTICS (TA = 25 °C; Supply= 3.0 V)SPEC TABLE TITLE (INSERT 5 COLUMN TABLE) Spec Table ConditionNotes: 9. 20% duty cyc

Plus de documents pour Matériel Cirrus Logic CS8130

Voir le document Cirrus-logic CS8130 Manuel d'utilisateur

Cirrus-logic CS8130 Manuel d'utilisateur (28 pages)

Commentaires sur ces manuels

Pas de commentaire

Cirrus-logic CS8130 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Cirrus-logic CS8130. Cirrus Logic CS8130 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Matériel Cirrus Logic CS8130

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Cirrus-logic CS8130