Cirrus-logic CS1680 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Cirrus-logic CS1680. Cirrus Logic CS1680 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Copyright Cirrus Logic, Inc. 2014
(All Rights Reserved)
Cirrus Logic, Inc.
http://www.cirrus.com
CS1680
Dimmable LED Driver IC
for Low-voltage Lighting
Features
Best-in-class Transformer Compatibility
- Magnetic Transformers
- Electronic Transformers
Best-in-class Dimmer Compatibility
- Leading-edge (TRIAC) Dimmers
- Trailing-edge Dimmers
High Efficiency
- Up to 80% for CS1680-00 Applications
- Up to 83% for CS1680-02 Applications
Flicker-free Dimming
5% Minimum Dimming Level
Cascade Boost-buck Topology with Constant-current
Output
- CS1680-00 Output Voltage 15V
- CS1680-02 Output Voltage 21V
Fast Startup
Tight LED Current Regulation: Better than ±10%
>0.9 Power Factor on Magnetic Transformers
Soft Start
Protections:
- Output Open/Short
- Boost Overvoltage
- Overcurrent Detection
- External Overtemperature Using NTC
Overview
The CS1680 is a cascade boost-buck dimmable LED
driver for the 12V halogen lamp-replacement market.
The CS1680 uses a Cirrus Logic proprietary intelligent
digital control that provides exceptional single-lamp and
multi-lamp transformer compatibility for non-dimmer sys-
tems and dimmer systems paired with electronic and
magnetic low-voltage transformers.
The CS1680 integrates a continuous conduction mode
(CCM) boost converter that provides transformer com-
patibility and dimmer compatibility. An adaptive digital
algorithm controls the boost stage and dimmer compati-
bility operation mode to enable flicker-free operation
down to 5% output current with leading-edge and trail-
ing-edge dimmers.
Applications
MR16 Lamps
All 12VAC/VDC Low-voltage Lighting Applications
Ordering Information
See page 15.
LED +
LED -
C
OUT
NTC
C
BST
D
BST
Q
BUCK
CS1680
VAC
BUCKGD
BSTOUT
9
CLAMP
BUCKZCD
BUCKSENSE
eOTP
12
2
13
R
CLAMP
R
S
C
NTC
R
BST
D1
12VAC/VDC
D2
V
rec t
V
BST
D
BUCK
Q
CLAMP
C5
VDD
GPIO
BSTSEN SE
BSTGD
C
rect
6
7
3
11
15
R
BUCK(Sense)
R
BST(Sense)
Q
BST
R4
Z2
D3
D4
GND
1
CTRL1
16
R
CTRL1
R1
C4
R
CTRL2
CTRL2
4
5
14
Q1
Z1
R5
C1 C3
R3
U1
D5
D6
R
rect
C2
Q2
L
BST
L
BUCK
R2
OCT’14
DS1055F1
Vue de la page 0
1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Dimmable LED Driver IC

Copyright  Cirrus Logic, Inc. 2014(All Rights Reserved)Cirrus Logic, Inc.http://www.cirrus.comCS1680Dimmable LED Driver ICfor Low-voltage LightingFea

Page 2 - 1. INTRODUCTION

CS168010 DS1055F1boost output voltage continues to fall and reaches thelowest threshold set by constant KDEC(on), the LEDoutput current is decreased a

Page 3 - 2. PIN DESCRIPTION

CS1680DS1055F1 11page 11). If the boost output voltage exceeds theovervoltage protection threshold, a BOP fault signal isgenerated. Boost overvoltage

Page 4 - 4 DS1055F1

CS168012 DS1055F1period T2BUCK. The controller then uses thetime TTBUCK to determine gate turn-on time.5.4.2 Current Sense Resistor ModelThe digital a

Page 5 - DS1055F1 5

CS1680DS1055F1 13When exiting reset, the chip enters startup and the ADCquickly (<15ms) tracks the external temperature to checkif it is below 120°

Page 6 - 3.3 Absolute Maximum Ratings

CS168014 DS1055F16. PACKAGE DRAWING mm inchDimension MIN NOM MAX MIN NOM MAXA -- -- 1.1 -- -- 0.043A1 0.05 -- 0.15 0.002 -- 0.006A2 0.85 -- 0.95 0.03

Page 7 - 4. TYPICAL PERFORMANCE PLOTS

CS1680DS1055F1 15Notes:1. Controlling dimensions are in millimeters.2. Dimensions and tolerances per ASME Y14.5M.3. This drawing conforms to JEDEC out

Page 8 - 5. GENERAL DESCRIPTION

CS168016 DS1055F1REVISION HISTORYContacting Cirrus Logic SupportFor all product questions and inquiries contact a Cirrus Logic Sales Representative. T

Page 9 - Voltage Threshold

CS16802 DS1055F11. INTRODUCTIONA typical schematic using the CS1680 for boost-buckapplications is shown on the previous page.A startup circuit provide

Page 10 - 5.3.2 Boost Stage Control

CS1680DS1055F1 32. PIN DESCRIPTIONPin NamePin # I/ODescriptionCTRL21INPeak Current — Connect a resistor to this pin to set the comparator threshold to

Page 11 - 5.4 Buck Stage

CS16804 DS1055F13. CHARACTERISTICS AND SPECIFICATIONS3.1 Electrical CharacteristicsTypical characteristics conditions: - TA=25°C, VDD= 12V, GND = 0 V-

Page 12 - 5.4.3 Zero-current Detection

CS1680DS1055F1 5Boost Gate DriverOutput Source Resistance ZBST(Source)- 19.9 - Output Sink Resistance ZBST(Sink)- 10.5 - Rise TimeCL=0.25nF-11-nsFal

Page 13

CS16806 DS1055F1Notes: 1. Threshold is characterized as a percentage of the full-scale boost output voltage, VBST(full)2. The CS1680 has an internal s

Page 14 - 6. PACKAGE DRAWING

CS1680DS1055F1 74. TYPICAL PERFORMANCE PLOTSFigure 3. UVLO CharacteristicsFigure 4. Supply Current vs. VoltageFigure 5. Turn On/Off Threshold Volta

Page 15 - 7. ORDERING INFORMATION

CS16808 DS1055F15. GENERAL DESCRIPTION5.1 OverviewThe CS1680 is a cascade boost-buck dimmable LEDdriver for the 12V halogen lamp-replacement market.Th

Page 16 - REVISION HISTORY

CS1680DS1055F1 9voltage to reach the regulation target set byconstant KMode1(target). If boost output voltage VBST isbelow the target regulation point

Commentaires sur ces manuels

Pas de commentaire